Bringing advanced technology to sensors

OEM wet/wet differential pressure sensor - Model PV1L

OEM differential pressure sensor PV1L

Product description

Featuring a 19 mm (~3/4”) diameter and a 26 mm (~1”) length, the PV1L model is our most versatile and our most robust OEM wet/wet differential pressure sensor. This model has been specifically designed to measure low differential pressures under high static pressures (up to 200 bar). The construction features a hermetically-sealed, fully-welded 316L stainless steel housing, which makes the sensor well-suited for demanding applications in harsh environments. The sensor utilizes the latest technologies to provide a highly-precise, stable and reliable pressure measurement.

The sensor integrates a single solid-state, piezoresistive MEMS silicon die which acts as the sensitive element and converts pressure into an electrical signal. Using advanced techniques of MEMS fabrication (like wet etching, anisotropic etching), a thin diaphragm is crafted inside the silicon die. The thickness of the diaphragm is individually adapted to each pressure range so as to get the highest possible sensitivity without breaking under full pressure load.

Thanks to the monocrystalline structure of the silicon, the pressure sensor exhibits no measurable hysteresis and provides an excellent repeatability, making it highly reliable and highly precise over years of operation.

Besides being very cost-efficient and well-suited for mass production, the silicon monolithic structure withstands overpressures to twice the pressure range without damage or effect on the future performance of the sensor and has a life expectancy of tens of millions of cycles. The sensor is also highly sensitive, exhibiting a high signal with a low power excitation, which is ideal for battery-operated systems.

For protection against media and for ease of integration, the silicon die is mounted and wire-bonded on a glass feedthrough (header) and integrated into a high quality, hermetically-sealed, fully-welded 316L stainless steel enclosure. The housing is filled with a silicone oil on both side and closed by two very thin 316L stainless steel diaphragms. The silicone oil and the diaphragms both reliably transmit the pressure to the die while isolating the latter from the media.

Each sensor is individually tested under various harsh environments and conditions as part of our stringent quality procedures. Each sensor must pass all tests in order to be delivered. An individual calibration report can be delivered with the sensor upon request.

Specifications

Physical characteristics
Pressure range 0 to 0.1 bar through 0 to 2 bar
Safe overpressure 1.5 x (positive side), 1.5 x (negative side)
Burst pressure 2 x (positive side), 2 x (negative side)
Line pressure 200 bar
Environmental characteristics
Storage temperature -40 to 125°C
Operating temperature extremes -40°C, 125°C
Maximum operating temperature span 140°C
Ambient temperature -40 to 125°C
Electrical characteristics
Power supply / excitation between 0.5 mA and 2 mA (1 mA typ.)
Typical output signal 0 ~ 150 mV
Bridge resistance at 25°C (77F) between 2.5 kΩ and 4.5 kΩ
Mechanical characteristics
Electrical connections wires, connector
Mechanical connections ⌀19mm
Materials available 316L Stainless steel, Hastelloy C276
Seal materials available FKM, EPDM, Silicone, NBR
Performance (depending on temperature compensation range)
Type of compensation uncompensated resistors polynomial
Compensated temperature range - -10 to 80°C -10 to 80°C
Linearity ±0.25%FS ±0.25%FS ±0.25%FS
Hysteresis ±0.005%FS ±0.005%FS ±0.005%FS
Repeatability ±0.005%FS ±0.005%FS ±0.005%FS
Zero offset ±20mV ±2mV ±2mV
Span offset ±0 ±0 ±0
Line pressure drift ±0.02 mV/bar ±0.02 mV/bar ±0.02 mV/bar
Temperature drift of Zero ±0.25%FS/K ±0.3mbar/K ±0.01%FS/K
Temperature drift of Sensitivity ±0.08%/K ±0.08%/K ±0.03%/K
Stability (per annum) ±0.1%FS ±0.1%FS ±0.1%FS

All values are typical values.