OEM pressure sensor - Model PS1L
Product description
Equipped with a threaded connection, the PS1L model is an OEM pressure sensor which can be conveniently mounted and integrated in an equipment. No additional part or bracketry are needed to hold the sensor in place. The design has been optimized for the pressures it is dedicated to.
The sensor integrates a solid-state, piezoresistive MEMS silicon die which acts as the sensitive element and converts pressure into an electrical signal. Using advanced techniques of MEMS fabrication (like wet etching, anisotropic etching), a thin diaphragm is crafted inside the silicon die. The thickness of the diaphragm is individually adapted to each pressure range so as to get the highest possible sensitivity without breaking under full pressure load.
Thanks to the monocrystalline structure of the silicon, the pressure sensor exhibits no measurable hysteresis and provides an excellent repeatability, making it highly reliable and highly precise over years of operation.
Besides being very cost-efficient and well-suited for mass production, the silicon monolithic structure withstands overpressures to twice the pressure range without damage or effect on the future performance of the sensor and has a life expectancy of tens of millions of cycles. The sensor is also highly sensitive, exhibiting a high signal with a low power excitation, which is ideal for battery-operated systems.
For protection against media and for ease of integration, the silicon die is mounted and wire-bonded on a glass feedthrough (header) and integrated into a high quality, hermetically-sealed, fully-welded 316L stainless steel enclosure. The housing is filled with a silicone oil and closed by a very thin 316L stainless steel diaphragm, both reliably transmitting the pressure to the die while isolating the latter from the media.
Each sensor is individually tested under various harsh environments and conditions as part of our stringent quality procedures. Each sensor must pass all tests in order to be delivered. An individual calibration report can be delivered with the sensor upon request.
Specifications
Physical characteristics | |
---|---|
Pressure range | 0 to 0.1 bar through 0 to 2 bar |
Pressure type | ✔ absolute ✔ vented gage ✔ sealed gage ✔ compound ✔ barometric |
Vacuum | possible, down to 50 μbar absolute |
Safe overpressure | 1.5 x |
Burst pressure | 2 x |
Environmental characteristics | |
---|---|
Storage temperature | -40 to 125°C |
Operating temperature extremes | -40°C, 125°C |
Maximum operating temperature span | 140°C |
Ambient temperature | -40 to 125°C |
Electrical characteristics | |
---|---|
Power supply / excitation | between 0.5 mA and 2 mA (1 mA typ.) |
Typical output signal | 0 ~ 150 mV |
Bridge resistance at 25°C (77F) | between 2.5 kΩ and 4.5 kΩ |
Mechanical characteristics | |
---|---|
Electrical connections | pins, leads, wires, connector |
Mechanical connections | G 1/4", 1/4"-18NPT and many others |
Materials available | 316L Stainless steel, Hastelloy, Titanium |
Seal materials available | FKM, EPDM, Silicone, NBR |
Performance (depending on temperature compensation range) | |||
---|---|---|---|
Type of compensation | uncompensated | resistors | polynomial |
Compensated temperature range | - | 0 to 50°C | 0 to 50°C |
Linearity | ±0.25%FS | ±0.25%FS | ±0.05%FS |
Hysteresis | ±0.005%FS | ±0.005%FS | ±0.005%FS |
Repeatability | ±0.005%FS | ±0.005%FS | ±0.005%FS |
Zero offset | ±20mV | ±2mV | ±2mV |
Span offset | ±0 | ±0 | ±0 |
Temperature drift of Zero | ±0.25%FS/K | ±0.02mV/K | ±0.01%FS/K |
Temperature drift of Sensitivity | ±0.03%/K | ±0.03%/K | ±0.03%/K |
Stability (per annum) | ±0.1%FS | ±0.1%FS | ±0.1mV |
All values are typical values.